RSSI model

The Received Signal Strength Indicator (RSSI) model collects information about the strength of the signal between different mesh devices and sends this data to a centralized point of the mesh network for further analysis. Use this model to simplify the process of monitoring the overall signal quality in a mesh network, for example a ligthing network in a office building, where the installer could utilize this model to ensure that the coverage of the network is sufficient.

Table of contents

• Properties and features
• Implementing the model
• Message format
  • Send RSSI data message
  • Reply status message
  • Message opcodes

The model is centered around the server. The server continuously takes samples with the RSSI data from the messages that arrive at the server’s mesh device. At a set interval, the server forwards a processed version of the data to the client. Each message received by the client is acknowledged with a reply to the server. The server expects this acknowledgement before it wipes the outgoing data buffer. If the message transaction is not successful within 30 seconds, the server will still wipe this data. While there is an ongoing data transfer between the client and the server, the raw data buffer will be wiped, and it will start accumulating any new samples that are added. This means that the server can collect data while you are waiting for a data transfer to complete.

The following figure shows an example network with four devices at the exact moment when an interval has expired and a the RSSI data message has been sent from the sever to the client.

Figure 1: Example network with four devices.

In this figure, the node 0x0001 is an implementation of the client model and the node 0x0002 is an implementation of the server model. The RSSI message contains all the collected data from the last interval, and the server has registered two links, one from the node 0x0003 and one from the node 0x0004.

See the following figure for the message flow of the mesh network from Figure 1 during a time interval.

Figure 2: Message flow during a time interval.

Properties and features

The RSSI model consists of two models:

• client model (ID 0x0006)
• server model (ID 0x0005)

The RSSI model does not generate its own data. It uses (leeches) metadata generated by messages passing from other model operations.

The server model sends the collected data to the client at a set time interval. All messages sent from the server are acknowledged by the client upon arrival. The time interval can be configured with the Configuration Model to suit the specific application.

The number of entries in one message depends on the number of unique links that has been registered since the last time a message was sent. By default, the server model raw database buffer can contain up to 20 unique link entries. This value can be altered by defining RSSI_DATA_BUFFER_SIZE with the desired maximal value in the preprocessor. When this buffer is full, the server model ignores attempts to add new entries until the current entries are sent and the buffer is wiped.

The maximal number of entries in a single on-air message is also equal to RSSI_DATA_BUFFER_SIZE. For this reason, use a value that will not allow a exessive amount of messages to go on air at the same time, since this will affect the on-air capacity.

Implementing the model

Before implementing the model, take note of the following requirements:

• Each server implementation must publish to the unicast address associated with the RSSI client implementation.
• When the server models are initially configured, the publish period must be set to a value greater than zero. Otherwise, the server will never publish any messages to the client.

Note

The steps that mention the API functions after the initialization step 1 are handled by the Configuration Model, but are reported here for the local configuration of each device.

To implement the RSSI client model on a device:

1. Initialize the model with rssi_client_init() from the model API.
2. Bind and set the app-key for the model through the access_model_application_bind() and access_model_publish_application_set() API functions.

To implement the RSSI server model on a device:

1. Initialize the model with rssi_server_init() from the model API.
2. Bind and set the application key for the model with the access_model_application_bind() and access_model_publish_application_set() API functions.
3. Set the publication address for the model with the access_model_subscription_add() API function (see the requirements mentioned above).
4. Set the publication period for the model with the access_model_publish_period_set() API function.
   • Before choosing the span of the time window, consider the granularity of the period between each message sent by the server. Since the server computes an average signal value before the message is sent to the client, you can only see the general trend of the signal strength from the last time window. If the time window gets too long, it can lead to overlooking of some of the finer details in the signal mapping. On the other hand, if the time window gets shorter, you must provide a sufficient number of samples to the server model to get consistent data. In this case, consider also the on-air footprint the model will make.

Message format

The RSSI model uses the following types of messages:

• Send RSSI data
• Reply status

Send RSSI data message

This message contains the data collected by the servers. The data is stored in an array that by default can contain up to 20 entries, depending on how many links the server has registered.

See the following table for the entry structure breakdown.

Reply status message

This message acknowledges that the server data has arrived to the client.

Message opcodes